Doing Things I Don’t Know How to Do

(Casita wiring schematic removed by request.)

Sometimes projects overwhelm me because I have no prior knowledge or experience to draw on.

Installation of the Fantastic Fan is one of those projects.

I suppose my fear of working with anything electrical goes back to the dire warnings of electrical shock and electrocution that my mother instilled on me thoughout my growing-up years — based on a near-death experience during her teenage years.

Anyway, I understand now that if the trailer is unplugged and one cable of the battery is removed (or the breakers turned off) that I’m not going to get fried.  But that’s about all I understand.

These connectors came with the Fantastic Fan

These connectors came with the Fantastic Fan

First of all, most Casitas come prewired for a Fantastic Fan.  The original owner of my trailer ordered it without a roof vent at all.  So there is no existing fan wiring to tie into.

I called Casita, and they said to tie into the dinette lighting.   They are wonderful people, but they are also extremely busy, and my dumb questions apparently frustrated them.  So all I know is that I need to tie into the dinette light wiring.

One size fits all. :)

One size fits all. 🙂

I found a DC diagram for the Casita and it shows me where the wires run.  I will have to lift the carpet inside the cupboards, find the  wires, then glue the carpet back down later.

I am going to have to run the wires under the carpet from the cupboard to the ceiling.  I have some heavy aluminum wire that I think I can create a fish tool from.

I have the wood spacer for the fan cut out.  Just need to sand and finish it.

So now I am down to trying to figure out how to follow the Fantastic Fan electrical directions.  They say, “Hook 12 volt power to fan.”

Two wires are attached to the fan, and the package includes two little blue connectors.  I have never seen connectors like these before.  So I do a web search for a tutorial.  Finally I find an article that says to slide the wires in from both sides and crimp in the middle.  But I don’t know if one crimp in the middle will keep the wires from vibrating apart.  Would it be better to crimp each wire separately near the middle of the little blue thing?  I have no clue.  I’m guessing it couldn’t hurt.

Then I start thinking that if I cut the trailer wires and connect the fan that probably the lights and bathroom fan, farther down the circuit, wouldn’t work unless the Fantastic Fan was switched on.  So I searched the web again and found diagrams of jumper wires that would apparently route the current around the fan if it was off.

So I did a little sketch of how I thought I needed to do a jumper wire and emailed it to a guy who has answered questions for me in the past.  Although he graciously replied, he apparently was amused and his reply was so flippant that I would never dare ask him another question again.  🙂

Next I needed to decide what size connectors to use inside the cabinet.  I know from experience with battery connectors that there is no way I can crimp a wire tightly enough to get it in the size connector that’s supposed to fit.  I finally find some connectors that say they replace several different sizes… kind of an all-in-one solution.

Fortunately I do know how to use them because I have seen my ex connect wires with that screw on type connector.

Once I get the wires fished and figure exactly where to connect them, mounting the fan should be fairly simple — because I have used butyl tape and self-leveling caulking before, so I’m not expecting any hidden monsters to jump out and bite me there!

We have some rain on the way, so this will probably take a while!

Needlework & Shorter Days

tatting practice

Tatted practice pieces

Although our days are still in the 90’s and high 80’s, the nights are getting cooler, and the days are noticeably shorter.

So I am working on learning tatting in the evenings.   I am getting the hang of it, but have a lot to learn about tensioning my stitches.  It is fun to play with — to see these amazing patterns that are made of nothing but half hitch knots develop!

I bought some tiny little girls purses and tote bags for adults to decorate with tatting for Christmas gifts.  It sure is a lot more fun to make gifts than to go out and try to find something appropriate to buy.  I do hope that the recipients will like them.

little girl's denim purse

A little girl's denim purse that will be festooned with tatted motifs and lace.

A start on an afghan to match Ron's

My afghan-in-the-making

I am also working on an afghan for myself to match one that I made for Ron last year.  They are twin-bed sized.  And they are great in the Aliner for putting over a blanket when we camp in cold weather.  So when I get this finished, our little camper beds will match again!

%d bloggers like this: